| EnviroSep provides Integrated Solutions, nationwide & worldwide, for Fluids Handling, Heat Transfer, and Energy Recovery |
| Call Us @ 843-546-7400 — EnviroSep World Headquarters - Georgetown, South Carolina USA |
| site map |
your location: Products > Steam & Condensate Systems > Condensate Pump/Pot Packaged Pumping System (CP) (Base-Mounted End-Suction Centrifugal Pump) Model CP-60
Condensate Pump/Pot Packaged Pumping System (CP) (Base-Mounted End-Suction Centrifugal Pump)
Model CP - 60
System OptionsCondensate Pump / Pot Packaged Pumping (CP)
Base-Mounted End-Suction Centrifugal Pump
The Model CP-60, Condensate Pump/Pot, Packaged Pumping System, is a manufactured, ready-to-install system designed for installation on process heat transfer sources. The Condensate Pump/Pot, Packaged Pumping System allows the heat transfer source to operate at optimum conditions by efficiently removing condensate, increasing the heat transfer efficiency. The result is substantial savings in energy costs at attractive pay-back periods because there is no Flash Steam Loss. Designed for efficient pumping of condensate, CP-60 is not vented to atmosphere, therefore there is no additional piping needed for a large vent. The CP-60 utilizes an End-suction, Base-mounted, ANSI rated, Centrifugal Pump which offers premium pumping of process fluids. The Condensate Pump/Pot is controlled by a proportional level transmitter, which is accessible through top entry, to modulate the discharge control valve, permitting continuous removal of condensate proportional to actual steam consumption. A UL-Listed, Industrial Control Panel is prewired to all electrical sources. The system carries as standard a UL-Listing as a Packaged Pumping System.
View detailed information on Model CP-60, Condensate Pump/Pot, Packaged Pumping System (PDF)
Legend
Approximate Dimensions: 158"H x 78"L x 48"WA. Condensate Inlet 10" FLG
B. Condensate Discharge 2" NPT
C. Relief Valve Outlet 4" NPT
D. Pump Drain ½" NPT
E. Receiver Tank 36"x 96"
F. Tank Drain ½" NPT
-
Additional / Oversized Condensate Inlet connection(s)
-
Oversized Condensate Receiver
-
Tank-mounted Pressure Gauge
-
Reflex Level Gauge Glass
-
Forged Steel or Cast Steel Gate Valves
-
Low-profile design for height restricted applications
-
Condensate Discharge Flowmeter with Panel-mounted Digital Display
-
Fabricated Square Tubing Frame
-
Duplex Pump Design with Automatic Secondary Pump Start on Primary Pump Failure
-
NEMA 4 or 4X Enclosure
-
All Stainless Steel Construction
Conditions of Operation
Max. Allowable Pressure / Temp: 150 psig / 450 oF
Modulating Discharge Rate: 60 gpm @ 115 ft.
30 ,000 lb/hr @ 115 ft.
Max. Instantaneous Discharge Rate: 180 gpm @ 95 ft.
Electrical Requirements: 15.1 FLA-480 Volts
29.2 FLA-240 Volts
Minimum Recirculation Flow Rate: 45 gpm @ 119 ft.
NOTES:
1. Savings are based on max. potential savings at max. pump capacity on 8400 hr./yr. of continuous operation
2. Steam costs at $5.00/MM Btu
3. Savings based on approx. calculations.
4. Savings are based on the elimination of Flash Loss; Actual savings are derived by actual site conditions.
EnviroSep offers Professional Engineering Service including complete facility, steam, and condensate system layout and design.
Regardless of system size, temperature, pressure, fluid medium, or space requirements, EnviroSep can provide solutions to all specialized needs.
For more information on how EnviroSep can provide your company with an Integrated Solution for your Fluids Handling, Heat Transfer, and/or Energy Recovery needs, use our quick & easy Online Quote Request Form, call our main office at 843-546-7400 (you can fax us at 843.546.7407) or
domestic water pumps | hot water pumps | steam & condensate pumps | boiler room pumps | wastewater heat recovery pumps | packaged pumps | misc. industrial pumps | electrical & pump controls | custom pumps | private label pumps || site map